Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

液体火箭发动机推进剂泵诱导轮与离心轮的匹配

为获得诱导轮离心轮周向匹配的时序效应对离心泵外特性以及压力脉动的影响规律，阐释相关作用机制，采用基于分离涡仿真（DES）的离心泵三维全流道数值仿真方法，引入熵产理论以及压力脉动强度系数等先进分析方法对不同匹配角度下离心泵内能量损失机制及压力脉动特性进行了研究。结果表明：离心轮诱导轮的时序效应对泵外特性有一定的影响，随着匹配角度的增加，扬程和效率均呈现先减小后缓慢增大的趋势，扬程变化为0.8%，效率变化为1.2%，其影响机制由不同匹配角度下叶轮通道分离涡、叶轮叶片尾迹以及靠近隔舌处扩压器通道回流涡变化决定；时序效应对离心轮扩压器动静干涉效应影响显著，当诱导轮叶片尾缘位于离心轮相邻主叶片中间位置时，能够有效消除3倍频成分，显著降低泵内压力脉动水平，其中动静干涉区域以及隔舌处扩压器叶片表面压力脉动平均降幅分别达到14.5%和16.7%。     

基于Ansys Fluent的近场翼尖涡数值模拟与分析

为了进一步研究飞机远场尾涡,提供网格分配及湍流模型的参考,并为整机模拟提供必要的参考依据,通过基于Ansys Fluent的数值模拟方法,研究了NACA0012机翼的近场翼尖涡流场,采用有限体积法求解不可压缩雷诺平均Navier-Stokes方程,其中雷诺应力项分别以S-A和Realizable k-ε模型封闭,模拟了近场翼尖涡卷起的过程,分析了机翼表面压力以及涡核参数,包括轴向涡量、涡核位置、涡核粘性等,并与风洞实验结果进行了对比。结果分析表明:基于局部O-网的六面体网格,RKE模型要优于S-A模型,与实验值更为吻合。     

基于预置动压的高超声速飞行器上升段轨迹设计

针对高超声速飞行器燃料最省上升轨迹的研究问题,为实现高超声速飞行器的燃料最省上升轨迹快速求解,对定动压情况下高超声速飞行器上升段轨迹特性进行了研究分析,给出了定动压情况下高超声速飞行器燃料最省上升轨迹的快速反解方法,总结分析了不同定动压下的上升轨迹特性,并在此研究的基础上提出了基于预置动压的高超声速飞行器上升段轨迹设计方法。该方法可以通过设计燃料最省的动压曲线,反解出该预置动压下的上升轨迹参数,得到一条近似燃料最省最优解的轨迹。仿真结果表明,经过解算得到的上升轨迹结果与高斯伪谱法得到的最优上升轨迹结果基本相似。     

基于ALE法的水陆两栖飞机船体着水性能分析

水陆两栖飞机的着水性能是体现其综合性能的重要因素之一.应用ALE法对三种水陆两栖飞机船体截面进行入水仿真计算,从着水载荷、喷溅性能及运动响应三个方面对着水性能进行综合评估.对比分析了直线型、带舭弯弧形、复合型三种构型截面在不同速度、不同重量下的压力分布、喷溅性能以及运动响应,得到了三种截面横向压力分布规律.计算结果显示相同状态下,喷溅性能复合型优于带舭弯弧形、带舭弯弧形优于直线型;过载复合型远大于带舭弯弧形,带舭弯弧形稍大于直线型,综合看来带舭弯弧形截面着水性能最佳.     

卫星AIT阶段推进系统压力参数处理方法

在双组元推进系统管路中,高压气路、氧路、燃路分别装有一个压力传感器,通过压力传感器的遥测参数获取相应管路中压力情况。文章以某双组元卫星为例给出整星装配、总装与测试（AIT）阶段卫星推进系统压力参数处理方法,为卫星压力参数的纵向数据比对提供判读依据。通过该方法可以间接检查相应管路的气密性。     

典型民机复合材料损伤分析及敲击检测

只有充分研究民机典型复合材料损伤机理,才能在复合材料的应用中最大限度地减少和避免其损伤,并且为复合材料的损伤修理奠定基础.通过对民机典型复合材料损伤的研究,分别从材料、设计、结构、制造与使用等方面入手,通过细观破坏机制阐述了层合复合材料的损伤.对部件的检测进行理论分析,找到易损伤位置,采用微观破坏机制运用敲击检测法对胶接复合材料就行了损伤检测,验证了二者的结合可提高检测效率及准确率.     

直升机舱内噪声主动控制技术研究

随着社会的发展和科学技术的进步,驾乘人员对直升机的舒适性提出了更高的要求,该要求使舒适性成为直升机产品竞争性的要素之一.而将直升机舱内振动与噪声保持在较低的水平则是满足舒适性的重要条件.本文针对直升机舱内噪声主动控制的研究进展进行了概述.首先简要介绍了直升机舱内噪声的产生与频谱特征,以及常见的噪声控制方法;之后针对主动噪声控制进行了分类,分别按照主动消声控制技术和主动结构声振控制技术进行了归纳总结,并讨论了所采用主动控制律的发展趋势;最后对直升机舱内噪声主动控制的发展进行了展望.     

航空发动机液压管路静压力损失分析及试验验证

液压机械装置(HMU)燃油管路的设计是否合理将直接影响到油液静压力的传递损失和各液压元件的工作特性.为了研究燃油管路内部流动损失机理,验证相关计算方法的置信度,针对典型管路静压力损失,采用锐边节流公式和短管节流公式进行了理论计算,并进行了CFD仿真分析,对计算结果进行了试验验证.计算与试验结果对比分析表明:液流的静压力损失主要出现在进口环腔与管路的交界处,管路下游液流的静压力与出口环腔内一致;锐边节流公式的计算结果相对偏大,而短管节流公式的计算结果更接近于试验值.